9 Simple Steps to Waterproofing Exterior Walls

“Your walls are the foundation of your house. The weather out there won’t be good for the exterior walls of your house. If you want your wall to be waterproof, you have to paint it. After dealing with rain, snow, wind, dust and heat of the outside environment, the paint will start peeling off.”

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

“The outer part of your home’s wall is usually covered with a lot of dust and dirt from the air. To ensure the efficiency of the process, you need to clear off the debris and dust thoroughly. The dirt and debris can be cleaned using a broom, brush, or scraper. Then wash it with a power washer.”

Step 3: Check out for the cracks and fill them up

Cracks and holes can develop over time on your exterior walls. Follow up the cleaning process with a thorough look at the cracks and holes on the wall to make sure proper weatherproofing is ensured. Simply fill them up with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The mixture of cement penetrated inside the cracks and seals them. Make sure you remove the loose cement from the wall before applying the cement.

Step 4: Add a layer of cement waterproofing sealer

To make sure your wall is waterproof, you need to apply a cement waterproofer. After applying the cement in the crevices, let it dry and then apply the waterproof paint sealer. Allow it to be dry.

Step 5: Pick the right water-proofer

There are a lot of products that are waterproof. You need to pick the right one for your wall. Pick the water-proofer based on whether the wall is concrete or silicate.

You can choose between a silicate-based concrete sealer and a concrete waterproof coating. Pick a plaster waterproof Additive that will strengthen your walls.

Step 6: Apply the water-proofer

Apply the water-proofer with a roller or brush. Give a thin coat first if you want to apply more than one layer. Allow the first coating to dry and then add the second one.

Step 7: Apply tar and heavy-duty membrane

If you want to add more strength to the layers, you need to use a tar-based pitch after the drying of the cement. It should be applied everywhere on your wall.

After that, you need to apply a heavy-duty plastic or rubber membrane, which will ensure the proper care of your walls

Step 8: Consider adding gravel

If you want to lay the drainage pipes, you need a proper base below the footer. The drainage pipes are going to get adequate support from a gravel base. Gravel is long- lasting and provides enhanced protection.

You need to lay the gravel along with the drainage pipe-cover. The gravel should be level near the footer. A covering for the pipe should be at least 3-inches.

Step 9: Add a fabric barrier

Attach the fabric barrier to the pipe. A fabric barrier will prevent the formation of dirt and keep your system clean. Then back-fill the trench and build the top of the dirt relatively high and let it settle for a while. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia

Conclusion:

Good waterproof gives your home a new life and strength to deal with weather-related issues. If you want good waterproof solutions for your walls, Magicrete is here to help. At a very low and affordable price, Magicrete can provide you proper weatherproofing.

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s”

Lea Jasper
Lea Jasper
Articles: 202

Leave a Reply

Your email address will not be published. Required fields are marked *